- 8 -
line of the vice opening – therefore the centre
of the work piece - will always “hit“ the centre
of the saw blade independent of the selected
work piece width.
Clamping round materials is no problem. The
prismatic groove ensures the safe and reliable
clamping of round materials. For thin, yet rela-
tively wide work pieces (up to 65 mm) there is
another groove on the top of the clamping jaw.
The round table itself is swivel-mounted: An
angle of plus/minus 45° produces all desired
mitres and the scale on the right also enables
exact and easy monitoring of the angle set-
ting. The round table has serrations every 15°,
but any and all “intermediate steps“ can be
set and fixed with a clamping fixture. Cross-
cutting work pieces by using the limit stop is
also possible with this device.
The saw head is kept in its upper home posi-
tion by spring tension. Important: For even
greater flexibility, the saw head can also be
laterally adjusted on the side using a knurled
screw. This minimises the “free” length of the
work piece outside the vice jaws, and for
angle cuts this ensures that the saw blade
does not collide with the vice jaws.
For saw head operation, i.e. to swivel the saw
head down while working with the saw, the
mechanical safety catch located on the saw
head in its home position must be unlocked
for your safety. To prevent accidental opera-
tion and therefore minimise the risk of injuries,
the saw head is arrested in its upper position
and can be unlocked with a small lever at the
horizontal grip.
This also unlocks the mechanical safety catch
for the swivelling saw blade protection: This
folds itself up when the saw head is lowered to
the work piece. The ergonomically placed
on/off button can then be pressed easily and
without risk.
6 Technical data
Dimensions and weights:
Device base: approx. 9” x 9”
(230 mm x 230 mm)
Device base height: approx. 2” (50 mm)
Height: approx. 8
7
/
16
“ (215 mm)
(in resting position of the
separating head)
Width: approx. 11
13
/
16
“ (300 mm)
(saw head at far right)
Jaw length of vice: 3
1
/
8
” (80 mm)
Span width: max. 1
6
/
8
“ (45 mm)
Weight: approx. 6 kg
Ø saw blade: 3
1
/
8
”; max 3
11
/
32
”
(80 mm; max. 85 mm)
Motor:
Voltage: 110-120 V
50/60 Hz
Power: 1.8 A
No-Load speed: 5400/min
7 Before beginning work
NOTE:
Safe and precise work is only then possible if
the device has been properly fastened with
screws to a worktop. There are drill holes in
the heel plate for this purpose.
CAUTION!
When fixing or transporting the device, always
disconnect the mains plug!
DANGER!
Never operate the Miter Saw without wearing
protective goggles!
Never use the Miter Saw to cut materials other
than wood, non-ferrous metals or plastics.
Only choose saw blades suitable for the mate-
rial to be cut.
8 Working with the KGS 80 Miter Saw
8.1 Cutting capacity
Work can begin after the device has been
fixed to a stable base. Additional preparations
are not necessary and the work piece to be
separated can be clamped into the vice and
cut in two. Please note the following maximum
sizes in dependence on the sawing angle:
How to read the table:
If, for example, you would like to cut a 1
3
/
16
”
inch squared timber in two at a 45° angle, it
may only have a maximum depth of
3
/
8
” inch.
Please note that these are only standard
values.
(8 Seiten)
(38 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern